STEP 3
Thank you for purchasing NewAge Products VersaRoll. We hope your
new VersaRoll gives you a long-lasting trouble-free flooring solution,
and have put together this instruction and care guide to help you
get the most out of your floor. Please read this package fully before
laying out your VersaRoll.
NewAge does NOT recommend gluing or taping your floor down to
the substrate.
NewAge does not recommend installing your floor outside, however
in such installs we recommend using a pressure sensitive adhesive to
attach the roll floor to the substrate.
Patterns of two pieces of roll floor may not align perfectly along the
seam when two mats are laid side by side.
The roll floor is heavy, and as such, we recommend 2 people to install
this floor.
STEP 1
Unpack and install product as soon as possible after you’ve received
it. The roll is wound tightly during transportation and it will unroll
and flatten easier if it is unrolled out of its packaging immediately
after purchase.
STEP 2
Make sure the surface you’re rolling the floor on is clean and dry.
Wipe up any chemical or oil spills before laying the floor down. If
there are any loose chunks of concrete or debris, remove those as
best as possible to avoid bumps in the floor. Finally, sweep, vacuum
or hose the garage floor down and allow it to dry fully before
installing your floor.
STEP 3
Now you can roll out your floor. For quickest installation, unroll the
roll floor on to the garage floor or driveway. Unrolling the floor on
the driveway with direct sunlight will flatten out the roll faster. Start
unrolling the roll floor at the garage entrance, and finish at the back
of the garage. Depending on how the floor is packaged, you may
need to flip the roll to get the pattern side up. The roll is heavy, so you
may want to have a helper to assist you in doing this.
STEP 4
Initially, the roll floor will have small bubbles, ripples or curl marks
in the floor. In colder climates, it may take 2-4 days for most curls or
ripples in the floor to flatten out. To make the roll floor lay flat, use
a large push broom to flatten out air trapped under the roll. Start
pushing at the center of the roll and work your way out to the ends
for best results. These curls and bumps are normal, as the floor was
wound tightly during shipping, and will need a few days to relax and
conform to your floor. If you need to park on the floor immediately,
you can do so after unrolling the floor, and do not have to wait until
all of the curls or ripples have flattened out.
STEP 5
Custom Fitting – If you’d like to trim the floor around edges or corners,
first allow the floor to fully relax in place for 2-4 days (up to 4 days
is suggested for colder climates). You can use a standard industrial
cutting knife or industrial scissors to cut the roll. If the roll is being
installed in extreme conditions, such as direct sunlight or a very cold
garage, the roll can expand or contract up to 3% (3-4 inches overall). If
you are custom cutting the roll, it is important to give the roll enough
time to adjust to the temperature in the garage before trimming.
If installing in a warmer season, leave about 1/8” gap around the
perimeter of the garage to allow for expansion and contraction of the
product. If installing in a colder season, leave about 3/8” gap around
the perimeter to allow for expansion in the summer months.
STEP 6
Taping around edges is not necessary. Because the roll can expand or
contract, it is best if the product is allowed to sit freely on the floor. If
you choose to tape the seam between two roll floors, we recommend
using indoor-outdoor carpet tape. If you find the roll is moving or
shifting on your floor, we recommend taping the floor down at the
front of the garage (inside the garage door), using indoor-outdoor
carpet tape.
INSTALL INSTRUCTIONS
VERSAROLL
need more information? try, WWW.NEWAGEPRODUCTS.COM or 1 877 306 8930 for answers to commonly asked questions.
STEP 4
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern